Intensifier Assembly STREAMLINE SL-VI PRO III 60 UHP WATERJET

UHP Waterjet SL-VI Pro III 60 HP Intensifier Unit

The UHP waterjet intensifier troubleshooting

1. Inlet water pressure is falling below 30 psi (2 bar) during stroke condition

2. Outlet booster pump pressure is falling below 100 psi (6.8 bar)

3. Water is leaking around the v-clamp on the filter head

4. High oil temperature resulting in shutdown

5. Low oil level resulting in shutdown

6. Hydraulic pressure but no high pressure water pressure

7. Erratic fluctuations in the operating pressure, or inability to reach or maintain set pressure

8. No hydraulic oil pressure

9. Pump shaft will not turn

10. Pump will not start

11. Console display and lights do not illuminate

12. Pump quits running

13. No control power

14. Red light on operator’s console is on

15. Hot surfaces on the high pressure cylinder components

16. Low cutting water pressure

	SL-VI Pro III 60 HP Intensifier Unit	72158354	Oil/Water Heat Exchanger Kit
72170165	Intensifier Assembly	72158346	Oil/Air Heat Exchanger Kit
05130091	Hydraulic Seal Cartridge	72158362	Combination Heat Exchanger Kit
72170157	Sealing Head Assembly	72183019	Electrical Assembly
72101190	Hydraulic Piston Assembly	72171147	Electrical Configuration, Line Start
20468634	Pneumatic Valve/Actuator Assembly	72157578	Electrical Kit, Hardware
72186207	Ultra-High Pressure Water Assembly	72155173	Electrical Kit, Circuit Breaker
72186225	Bulkhead Pipe Assembly	72155421	Electrical Kit, Low Voltage Controls
72155629	Low Pressure Water Filter Assembly	72155348	Electrical Kit, High Voltage Controls
72182795	Hydraulic Power Package	72155223	Electrical Kit, Motor Starter
72159791	D08 Manifold Assembly	72166221	Power Factor Correction Kit
72112043	Hydraulic Manifold Assembly	72182629	Proportional Pressure Control
72159197	Hydraulic Hose Connections	72186365	Redundant Kit
72183328	Reservoir Assembly

Trouble shouting for UHP waterjet intensifier pump

1. Hydraulic oil leaking from the weep hole in the hydraulic cylinder head18. Water leaking from the weep hole in the hydraulic cylinder head

2. Water leaking from the weep hole in the hydraulic cylinder head

3. Water leaking from the weep hole in the hydraulic cylinder head

4. Water leaking from the weep hole in the sealing head

5. Water leaking from the weep hole in the sealing head gland nut

6. Water leaking from the weep hole in the UHP cylinder flange

7. Water leaking from the weep holes in the dump valve

	High Pressure Tube Coning Tools	20478997	UHP Valve/Actuator Assembly, NO
	High Pressure Tube Threading Tools		UHP Pressure Fitting and Valve Assemblies
	Maintenance Tools and Lubricants	72186207	Ultra-High Pressure Water Assembly
	Indexed Focusing Tubes	72183019	Electrical Assembly (Optional)
	Diamond Orifice	72186225	Bulkhead Pipe Assembly
	UHP Pressure Filter Assemblies	72183328	Reservoir Assembly
	UHP Pressure Swivel Pro Assemblies	72182795	Hydraulic Power Package
	Nozzle Tubes	72159197	Hydraulic Hose Connections
	IDE Pro Abrasive Nozzle Assembly	72185965	Cover Assembly (Optional)
20480707	Autoline™ Pro Abrasive Nozzle Assembly	72158536	Door Kit (Optional)
	Integrated Wear Insert/Orifice Assemblies	72186365	Redundant Kit (Optional)
20480359	UHP Valve/Actuator Assembly, NC

UHP waterjet intensifier pump parts

The 90,000 psi UHP waterjet intensifier pump is a device used to generate extremely high pressure for use in water cutting applications. This type of pump usually consists of a pump body, an electric motor or diesel engine and a booster system.

90,000 psi UHP Water cutting is a process that cuts materials by pressurizing water to extremely high pressure and spraying it through a nozzle. Ultra-high pressure water cutting can cut on a variety of materials, including metal, stone, concrete and composite materials.

05146592	Gasket, Topworks Support	72162253	Plunger
20476377	Support, Topworks	05130091	Hydraulic Seal Cartridge
10118206	O-Ring, 1.31 x 1.56 x .13	72175989	Bushing Retainer Flange
05144514	Hydraulic Cylinder	72158494	UHP Seal Assembly
05098991	Socket Head Screw, 3/8-16 x 3-3/4	72166738	UHP Cylinder
95688743	Lock Washer, .38	72163802	Liner
72101190	Piston Assembly	20474325	Stud, 1-1/8-12 x 18.31
10074771	O-Ring, 5.25 x 5.50 x .13	72170157	Sealing Head Assembly
05120092	Backup Ring, 5.25 x 5.50 x .13	72178493	Flange Assembly
72175997	Hydraulic Cylinder Head	20464590	Flat Washer, 1.13
05097886	Socket Head Screw, 3/4-16 x 2-1/4	20461761	Hex Nut, 1-1/8-12
05144183 / 05144191	Spacer Assembly, Proximity Switch	20489339	Adapter, JIC/Pipe, .50 x .38
72141569 72134224 95119012	Kit, Proximity Switch	72176756	O-Ring, 3.88 x 4.25 x .19

90,000 psi UHP waterjet pump usually has the following characteristics:

1.High-pressure output: The pump is capable of increasing water pressure to 90,000 psi (pounds per square inch), providing powerful cutting power.

2. Booster system: Pumps are usually equipped with a booster system to boost the low-pressure water flowing out of the pump body to the required ultra-high-pressure water.

3. Electric Motor or Diesel Engine: Pumps are typically driven by an electric motor or diesel engine, which provides enough power to push the flow of water and create the required pressure.

4. Safety measures: Ultra-high pressure water cutting booster pumps usually have safety measures, such as pressure regulating valves, pressure relief valves and emergency stop devices, to ensure the safety of operators.

80084759	Rebuild Kit	05129481	O-Ring, 1.0 x 1.13 x .06
05130109	Seal Bushing	05013024	O-Ring, 1.25 x 1.38 x .06
05015060	Packing Ring	05129515	Backup Ring
10193522	O-Ring, 1.19 x 1.38 x .09	05027255	Packing Seal
05050760	Backup Ring

72165539	Sealing Head	05116751	Poppet Pin
20481660	Gland	05147863	Compression Spring
20492123	Retaining Ring	20492131	Dowel Pin
10085371	Ball	10146082	O-Ring, 1.69 x 1.88 x .09
72101570	Seat	72117819	Spare Parts Kit
05116561	Discharge Poppet	72135447	Spare Parts Kit

90000 psi UHP waterjet price

The price may change with time and region. The price of UHP waterjet pump is affected by many factors, including brand, model, function and supplier. Generally speaking, a 90000 psi UHP waterjet pump is For high-end equipment, the price may be relatively high. They can be more expensive than regular waterjet pumps because they require special designs and materials that can withstand higher pressures. In addition, brand awareness and after-sales service may also have an impact on price.
If you are interested in 90000 psi UHP waterjet pump, contact win-win waterjet for accurate price and details. They will be able to provide quotes and advice based on your specific needs.

72101205	Ram Piston, 5.50	05049994	Backup Ring, 1.50 x 1.75
05074380	Clevis Pin	05087713	O-Ring, 1.25 x 1.50 x .13
05049887	Setscrew	05120118	Seal Assembly
10148757	Check Valve Assembly	05120100	Bearing
05088364	Retaining Ring	72168337	Spare Parts Kit

Maintenance of 90000 psi UHP waterjet pump’s dump valve

1. Turn the air supply off.

2. Remove the air supply hose from the valve assembly.

3. Loosen and remove the high pressure gland connections and the drain connection.

4. Remove the valve and actuator assembly from the machine.

5. Loosen the cylinder head on the actuator.Unscrew and remove the actuator from,the valve body.

6. Unscrew the UHP adapter and remove,the adapter and valve seat.

7. Remove the stem, SST backup ring and brass backup ring from the valve body.

8. Remove the seal assembly by pushing it, with the seal push tool (P/N 20470413).The assembly must be pushed out.through the actuator port in the top of the valve body.

9. Discard the stem, brass backup ring, seal assembly and valve seat.

10. Clean and inspect the valve body, being careful not to damage or scratch the bore.

20468617	Valve Body	10074714	O-Ring, 2.44 x 2.63 x .09
10178697	Valve Seat	10074565	O-Ring, 2.25 x 2.38 x .06
20451557	UHP Adapter	BV501184	Piston
72112069	Seal Assembly	20452965	UHP Collar, .38
20475874	Backup Ring, Bronze	20452956	UHP Gland, .38
20475878	Valve Stem	20452959	UHP Collar, .25
20468601	Pneumatic Cylinder	20452962	UHP Gland, .25
BV601184	Cylinder Head	20475882	Backup Ring, SST
20477518	Spare Parts Kit

The following are some suppliers that may supply 90,000 psi UHP waterjet pumps. These suppliers have certain reputation and experience in the waterjet cutting industry and can provide high-quality UHP waterjet pumps and related equipment.